3D Systems SLA 750 Series Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 101

3D Systems SLA 750 Series Скачать руководство пользователя страница 14

Inside of printer

2.4 Chemical Safety

IRRITANT! Always wear chemical-resistant gloves, goggles, and protective clothing when handling material . Avoid

skin contact . Avoid breathing material fumes .

• Always wear approved goggles, nitrile gloves and protective clothing when working near materials or with partially cured

parts.

• Wearing contact lenses when working with materials is not recommended.
• Always wear chemical-resistant gloves whenever handling materials or partially cured parts. Recommended gloves are 100%

Nitrile. Latex gloves are not chemical-resistant and are not recommended.

• Always work in a well ventilated area when using materials. Avoid breathing vapors.
• Always wash skin thoroughly with mild soap and COLD water after working with materials. DO NOT USE HOT WATER OR

SOLVENTS to wash hands, as it will result in quick absorption through the skin.

• Use extreme care when handling solvents used to remove excess material from uncured parts. These solvents (e.g.,

denatured alcohol, isopropyl alcohol) are very flammable.

• Keep all materials away from heat, sparks and flame. Material containers may rupture when exposed to extreme heat.

Use National Fire Protection Association Class B extinguishers such as carbon dioxide, dry chemical, or foam .

MATERIAL CHARACTERISTICS
The photopolymers used in stereolithography may be hazardous if handled improperly. Repeated skin contact

with materials may cause sensitization. Consult the manufacturer's Material Safety Data Sheet / Safety Data Sheet

(MSDS/SDS) for information on specific materials. For further information on this and related topics, consult the

3D Systems - Materials website at

https://support.3dsystems.com/s/article/materials-materials?language=en_US

support.3dsystems.com/s/article/materials-materials?language=en_US

3D Systems, Inc.

10

p/n 40-D150, Rev. C

«
...
12
13
14
15
16
...
»

Содержание SLA 750 Series






































































































Отзывы:

Нет отзывов