3D Systems SLA 750 Series Скачать руководство пользователя страница 47

Страница: 47 / 101

2. Tap on the Move Increment box (2) icon under the Elevator section.
3. Enter a value of 3" inches greater than the Start Position in the Move Increment (3) box and tap Move. Print platform will

raise 3".

4. Tap Set To Current Position to set the new Drain Position under the Elevator Settings column section (4).

6.5.3 Setting platform offload position

Setting the offload position will be dependent on two factors.

1. Using an Transfer Cart to remove the print platform.
2. Manually offloading the print platform by hand.

Setting the Offload Position will be determined by the

Drain Position

value.

To set the Offload Position for use of Transfer Cart

1. From the UI, tap on Elevator & Recoater (1) near the bottom tray and tap on More Settings.

3D Systems, Inc.

p/n 40-D150, Rev. C

Содержание SLA 750 Series






































































































Результаты поиска

Содержание SLA 750 Series

Отзывы:

3D Systems SLA 750 Series, Руководство пользователя, Страница: 47 / 101

Результаты поиска

Содержание SLA 750 Series

Отзывы: