3D Systems SLA 750 Series Скачать руководство пользователя страница 46

Страница: 46 / 101

Note: If the Start Position is not set, the elevator will move to the original default Start Position during

printing.

Any time the print platform is removed and reinstalled, it is advised that Move to Start be selected to make sure that all settings

have been retained for optimal printing. If not, you will need to repeat the preceding steps to reset your Start Position.

Note: After setting the Start Position, there may be bubbles in the MDM. Bubbles must be removed before

printing. To remove bubbles, follow the instructions here.

6.5.2 Setting platform drain position

Setting the Drain Position will be determined by the

Start Position

value.

To set the Drain Position:

1. From the UI, tap on Elevator & Recoater (1) near the bottom tray and tap on More Settings.

3D Systems, Inc.

p/n 40-D150, Rev. C

Содержание SLA 750 Series






































































































Результаты поиска

Содержание SLA 750 Series

Отзывы:

3D Systems SLA 750 Series, Руководство пользователя, Страница: 46 / 101

Результаты поиска

Содержание SLA 750 Series

Отзывы: