3D Systems SLA 750 Series Скачать руководство пользователя страница 42 | Manualshive

Страница: 42 / 101

3D Systems SLA 750 Series Скачать руководство пользователя страница 42

6.5 Elevator and Recoater

1

Elevator
Current Position: Shows the current position of the elevator relative to the home position.
Move To: Move to distance fom home (zero).
Move Increments: Set specified lengths when manually moving the elevator.
Velocity: Specifies the elevator speed, in inches per second (ips), during manual motion. The default is 1.0 ips. The

recommended range is 0.1 to 3.0 ips. This setting does not affect the applicator speed during printing. Set this value

inside this box.
Top/Bottom: Manually move the elevator up or down.
Move To Offload: Move the elevator to its print offload position as defined in the Set Offload settings.
Move To Start: Move the elevator to its start position.
Move To Home: Move the elevator to its home position.
Move To Drain: Move the elevator to its drain position as defined in the Drain Platform Settings.
STOP: Stop the current motion.

3D Systems, Inc.

38

p/n 40-D150, Rev. C

«
...
40
41
42
43
44
...
»

Содержание SLA 750 Series






































































































Отзывы:

Нет отзывов