3Com VCX V7111 Скачать руководство пользователя страница 46

Страница: 46 / 464

3Com

VCX V7111 VoIP Gateway User Guide

Assigning the V7111 Gateway IP Address

To assign an IP address to the V7111 gateway use one of the following methods:

HTTP using a Web browser (see

Assigning an IP Address Using HTTP

BootP

(see

Assigning an IP Address Using BootP

Voice Menu using a standard touch-tone telephone connected to one of the FXS analog

ports (see

Assigning an IP Address Using the Voice Menu Guidance

). This method does

not apply to FXO gateways.

The embedded Command Line Interface (CLI) accessed using Telnet or RS-232 (see

Assigning an IP Address Using the CLI

DHCP

(see

Using DHCP

Use the Reset button at any time to restore the V7111 networking parameters to their

factory default values (see

Restoring Networking Parameters to their Initial State

Assigning an IP Address Using HTTP

To assign an IP address using HTTP:

Disconnect the V7111 gateway from the network and reconnect it to your PC using one
of the following two methods:

Use a standard Ethernet cable to connect the network interface on your PC to a port

on a network hub / switch. Use a second standard Ethernet cable to connect the
V7111 to another port on the same network hub / switch.

Use an Ethernet cross-over cable to connect the network interface on your PC

directly to the V7111 gateway.

Change your PC’s IP address and subnet mask to correspond with the V7111 factory
default IP address and subnet mask, shown in

Table 14

. For details on changing the IP

address and subnet mask of your PC, see Windows™ Online Help (Start > Help).

Access the V7111 Embedded Web Server (see

Accessing the Embedded Web Server

In the Quick Setup screen (shown in

Figure 20

), set the V7111 IP Address, Subnet Mask

and Default Gateway IP Address fields under IP Configuration

to correspond with your

network IP settings.

If your network does not feature a default gateway, enter a dummy

value in the Default Gateway IP Address field.

Click

Reset

, and then at the prompt, click

; the V7111 gateway applies the changes

and restarts.

Содержание VCX V7111

















































































































































































































































































































































































































































































Результаты поиска

Содержание VCX V7111

Отзывы:

Похожие инструкции для VCX V7111

Бренды по названию

Популярные бренды

3Com VCX V7111, Руководство пользователя

Результаты поиска

Содержание VCX V7111

Отзывы:

Похожие инструкции для VCX V7111

Бренды по названию

Популярные бренды