3Com VCX V7111 Скачать руководство пользователя страница 188

Страница: 188 / 464

188

3Com

VCX V7111 VoIP Gateway User Guide

Figure 67

Regional Settings Screen

Enter the time and date where the gateway is installed.

Click

Set Date & Time

; the date and time are automatically updated.

After performing a hardware reset, the date and time are returned to their defaults
and should be updated.

To load a configuration file to the gateway:

Open the Regional Settings screen (

Advanced Configuration

menu >

Regional Settings

);

the Regional Settings screen is displayed (shown in

Figure 67

Click

Browse

adjacent to the file you want to load.

Navigate to the folder that contains the file you want to load.

Click the file and click the

Open

button; the name and path of the file appear in the field

beside the

Browse

button.

Click the

Send File

button that is next to the field that contains the name of the file you

want to load. An exclamation mark in the screen section indicates that the files loading
does not take effect on-the-fly (for example, CPT file).

Repeat Steps 2 to 5 for each file you want to load.

Содержание VCX V7111

















































































































































































































































































































































































































































































Результаты поиска

Содержание VCX V7111

Отзывы:

3Com VCX V7111, Руководство пользователя, Страница: 188 / 464

Результаты поиска

Содержание VCX V7111

Отзывы: