manualshive.com logo in svg

3Com 3Com SuperStack 3 Switch 3800 Family, Руководство пользователя

Поделиться
Скачать
3Com 3Com SuperStack 3 Switch 3800 Family Скачать руководство пользователя страница 96

6-2

C

HAPTER

 6: S

WITCH

 F

ORWARDING

 D

ATABASE

 (FDB)

■

Permanent entries

 — Permanent entries are retained in the 

database if the Switch is reset or a power off/on cycle occurs. The 
system administrator must make entries permanent. A permanent 
entry can either be a unicast or multicast MAC address. All entries 
entered by way of the command-line interface are stored as 
permanent. The Switch can support a maximum of 64 permanent 
entries.

PACE Prioritization

For devices supporting PACE, the Switch 3800 can be configured to 
recognize PACE modified addresses. When present, the Switch assigns 
PACE traffic to the high priority queue within the Switch.

Recognition of PACE traffic is controlled by the following commands:

enable pace

disable pace

How FDB Entries are

Added

Entries are added into the FDB in two ways:

■

The Switch can learn entries. That is, the Switch updates its FDB 
with the source MAC address from a packet, the VLAN, and the 
port identifier on which the source packet is received.

■

You can enter and update entries using a MIB browser, an SNMP 
Network Manager, or the command-line interface, as described in 
the next section.

SW3800.BK  Page 2  Tuesday, May 5, 1998  5:20 PM

Содержание 3Com SuperStack 3 Switch 3800 Family























































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды