3Com 3Com SuperStack 3 Switch 3800 Family Скачать руководство пользователя страница 126

Страница: 126 / 182

8-14

HAPTER

8: IP U

NICAST

OUTING

disable rip {vlan <name> | all}

Disables RIP for one or more VLANs. When RIP is disabled, the
parameters are not reset to their defaults, and the states are not
cleared.

Disables RIP for a VLAN causes all routes learned from that VLAN
to be advertised with a GarbageTime metric of 16, before being
deleted from the route table.

disable rip aggregation

Disables the RIP aggregation of subnet information on a RIP
version 2 interface.

disable rip splithorizon

Disables split horizon.

disable rip poisonreverse

Disables poison reverse.

disable rip triggerupdate

Disables triggered updates.

disable rip exportstatic

Disables the filtering of static routes.

unconfig icmp

Resets all ICMP settings to the default values.

unconfig irdp

Resets all router advertisement settings to the default values.

unconfig rip {vlan <name> | all}

Resets all RIP parameters to the default VLAN. Does not change
the enable/disable state of the RIP settings.

Table 8-6

Router Reset and Disable Commands (continued)

Command

Description

SW3800.BK Page 14 Tuesday, May 5, 1998 5:20 PM

Содержание 3Com SuperStack 3 Switch 3800 Family























































































































































































Результаты поиска

Содержание 3Com SuperStack 3 Switch 3800 Family

Отзывы:

Бренды по названию

Популярные бренды

3Com 3Com SuperStack 3 Switch 3800 Family, Руководство пользователя

Результаты поиска

Содержание 3Com SuperStack 3 Switch 3800 Family

Отзывы:

Бренды по названию

Популярные бренды