manualshive.com logo in svg

3Com 3Com SuperStack 3 Switch 3800 Family, Руководство пользователя

Поделиться
Скачать
3Com 3Com SuperStack 3 Switch 3800 Family Скачать руководство пользователя страница 74

4-20

C

HAPTER

 4: C

OMMANDS

RIP Commands

Table 4-17 describes the commands used to configure the RIP protocol.

Table 4-17   

RIP Commands 

Command

Description

show rip {vlan <name> | all}

Displays RIP configuration and statistics for one or more 
VLANs. Display includes the state for RIP settings, and 
interface states. Statistics include the following:

■

Packets transmitted

■

Packets received

■

Bad packets received

■

Bad routes received

■

Number of RIP peers

■

Peer information

enable rip 

Allows you to enable RIP.

disable rip

Allows you to disable RIP.

config rip add {vlan <name> | all}

Allows you to configure RIP on an IP interface. If no 
VLAN is specified, then “all” is assumed. When an IP 
interface is created, per interface RIP configuration is 
enabled by default.

config rip delete {vlan <name> | all}

Allows you to disable RIP on an IP interface. When RIP 
is disabled on the interface, the parameters are not 
reset to their defaults.

enable rip aggregation

Allows you to enable RIP aggregation of subnet 
information on a RIP version 2 interface. The default 
setting is enabled.

disable rip aggregation

Allows you to disable the RIP aggregation of subnet 
information on a RIP version 2 interface.

enable rip splithorizon

Allows you to enable the split horizon algorithm for 
RIP. Default setting is enabled.

disable rip splithorizon

Allows you to disable split horizon.

enable rip poisonreverse

Allows you to enable the split horizon with 
poison-reverse algorithm for RIP. The default setting is 
enabled.

disable rip poisonreverse

Allows you to disable poison reverse.

enable rip triggerupdate

Allows you to enable triggered updates. 

Triggered 

update

s are a mechanism for immediately notifying a 

router’s neighbors when the router adds or deletes 
routes, or changes the metric of a route. The default 
setting is enabled.

disable rip triggerupdate

Allows you to disable triggered updates.

(continued)

SW3800.BK  Page 20  Tuesday, May 5, 1998  5:20 PM

Содержание 3Com SuperStack 3 Switch 3800 Family























































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды