manualshive.com logo in svg

3Com 3Com SuperStack 3 Switch 3800 Family, Руководство пользователя

Поделиться
Скачать
3Com 3Com SuperStack 3 Switch 3800 Family Скачать руководство пользователя страница 105

STP Configurations

7-7

When the Switches in this configuration start up, STP configures each 
STP domain such that there are no active loops in the topology. STP 
could configure the topology in a number of ways to make it loop-free. 

In Figure 7-4, the connection between Switch A and Switch B is put 
into blocking state, and the connection between Switch Y and Switch Z 
is put into blocking state. After STP converges, all the VLANs can 
communicate, and all bridging loops are prevented.

The VLAN 

Marketing

, which has not been assigned to any STPD, 

communicates using all five Switches. The topology has no loops, 
because STP has already blocked the port connection between Switch 
A and Switch B, and between Switch Y and Switch Z.

SW3800.BK  Page 7  Tuesday, May 5, 1998  5:20 PM

Содержание 3Com SuperStack 3 Switch 3800 Family























































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды