3Com 3Com SuperStack 3 Switch 3800 Family Скачать руководство пользователя страница 71

Страница: 71 / 182

Switch 3800 Commands

4-17

IP ARP Commands

Table 4-14 describes IP ARP commands.

disable bootp vlan [<name> | all]

Allows you to disable the generation and processing
of BOOTP packets.

enable bootprelay

Allows you to enable the BOOTP relay function on
the router.

disable bootprelay

Allows you to disable the BOOTP relay function on
the router.

config bootprelay add <ipaddress>

Allows you to add IP addresses to be used as IP
destinations to forward BOOTP packets.

config bootprelay delete [<ipaddress> | all]

Allows you to delete one or all IP addresses that
were used as IP destinations to forward BOOTP
packets.

Table 4-13

Basic IP Commands (continued)

Command

Description

Table 4-14

IP ARP Commands

Command

Description

show iparp {<ipaddress> | vlan <name> |

all | permanent}

Displays the current

Address Resolution Protocol

(ARP) cache for a selected IP address, VLAN, or all
entries. With no options, information for all
VLANs is displayed.

Information displayed includes IP address, MAC
address, aging timer value, VLAN name, VLANid,
and port number.

clear iparp [<ipaddress> | vlan <name> |

all]

Allows you to remove dynamic entries in the IP
ARP table.

config iparp add <ipaddress> <mac_address>

Allows you to add a permanent IP ARP entry to
the system. The IP address is used to match the
IP interface address to locate a suitable interface.

config iparp delete <ipaddress>

Allows you to delete an IP ARP entry from the
table.

SW3800.BK Page 17 Tuesday, May 5, 1998 5:20 PM

Содержание 3Com SuperStack 3 Switch 3800 Family























































































































































































Результаты поиска

Содержание 3Com SuperStack 3 Switch 3800 Family

Отзывы:

Бренды по названию

Популярные бренды

3Com 3Com SuperStack 3 Switch 3800 Family, Руководство пользователя

Результаты поиска

Содержание 3Com SuperStack 3 Switch 3800 Family

Отзывы:

Бренды по названию

Популярные бренды