manualshive.com logo in svg

3Com 3Com SuperStack 3 Switch 3800 Family, Руководство пользователя

Поделиться
Скачать
3Com 3Com SuperStack 3 Switch 3800 Family Скачать руководство пользователя страница 136

9-10

C

HAPTER

 9: S

TATUS

 M

ONITORING

 

AND

 S

TATISTICS

Logging Commands

The commands described in Table 9-4 allow you to do the following:

■

Configure logging options

■

Reset logging options

■

Display the log

■

Clear the log

Table 9-4   

Logging Commands 

Command

Description

config log display {<priority>} 
{<subsystem>}

Allows you to configure the real-time log display. 
Options include:

■

priority — Filters the log to display message with 
the selected priority or higher (more critical). 
Priorities include critical, warning, and informational. 
If not specified, informational priority messages and 
higher are displayed.

■

subsystem — Filters the log to display messages 
associated with the selected Switch subsystem. 
Subsystems include Syst, STP, Brdg, SNMP, Telnet, 
VLAN, and Port. If not specified, all subsystems are 
displayed.

config syslog <ip_address> <facility> 
{<priority>} {<subsystem>}

Allows you to configure the syslog host address and 
filter messages sent to the syslog host. Options include:

■

ipaddress — The IP address of the syslog host.

■

facility — The syslog facility level for local use.

■

priority — Filters the log to display message with 
the selected priority or higher (more critical). 
Priorities include critical, warning, and informational. 
If not specified, only critical priority messages and 
are sent to the syslog host.

■

subsystem — Filters the log to display messages 
associated with the selected Switch subsystem. 
Subsystems include Syst, STP, Brdg, SNMP, Telnet, 
VLAN, and Port. If not specified, all subsystems are 
sent to the syslog host.

enable log display

Allows you to enable the log display.

enable syslog

Allows you to enable logging to a remote syslog host.

disable log display

Allows you to disable the log display.

disable syslog

Allows you to disable logging to a remote syslog host.

(continued)

SW3800.BK  Page 10  Tuesday, May 5, 1998  5:20 PM

Содержание 3Com SuperStack 3 Switch 3800 Family























































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды