3Com 3Com SuperStack 3 Switch 3800 Family Скачать руководство пользователя страница 121

Страница: 121 / 182

Configuring DHCP/BOOTP Relay

8-9

Table 8-4 describes the commands used to configure the ICMP
protocol.

disable rip splithorizon

Disables split horizon.

disable rip poisonreverse

Disables poison reverse.

disable rip triggerupdate

Disables triggered updates

disable rip exportstatic

Disables the filtering of static routes.

unconfig rip {vlan <name> | all}

Resets all RIP parameters to the default VLAN. Does not
change the enable/disable state of the RIP settings.

Table 8-3

RIP Configuration Commands (continued)

Command

Description

Table 8-4

ICMP Configuration Commands

Command

Description

enable icmp redirects {vlan <name> |

all}

Enables generation of ICMP redirect messages on one or
more VLANs. The default setting is enabled.

enable icmp unreachables {vlan <name> |

all}

Enables the generation of ICMP unreachable messages on
one or more VLANs. The default setting is enabled.

enable icmp useredirects

Enables the modification of route table information when an
ICMP redirect message is received. The default setting is
disabled.

enable irdp {vlan <name> | all}

Enables the generation of ICMP router advertisement
messages on one or more VLANs. The default setting is
enabled.

config irdp [multicast | broadcast]

Configures the destination address of the router
advertisement messages. The default setting is broadcast.

config irdp <mininterval>

Configures the router advertisement message timers, using
seconds. Specify:

■

mininterval — The minimum amount of time between
router advertisements. The default setting is 450 seconds.

■

maxinterval — The maximum time between router
advertisements. The default setting is 600 seconds.

■

lifetime — The default setting is 1,800 seconds.

■

preference — The preference level of the router. An IRDP
client always uses the router with the highest preference
level. Change this setting to encourage or discourage the
use of this router. The default setting is 0.

unconfig icmp

Resets all ICMP settings to the default values.

(continued)

SW3800.BK Page 9 Tuesday, May 5, 1998 5:20 PM

Содержание 3Com SuperStack 3 Switch 3800 Family























































































































































































Результаты поиска

Содержание 3Com SuperStack 3 Switch 3800 Family

Отзывы:

Бренды по названию

Популярные бренды

3Com 3Com SuperStack 3 Switch 3800 Family, Руководство пользователя

Результаты поиска

Содержание 3Com SuperStack 3 Switch 3800 Family

Отзывы:

Бренды по названию

Популярные бренды