manualshive.com logo in svg

3Com 3Com SuperStack 3 Switch 3800 Family, Руководство пользователя

Поделиться
Скачать
3Com 3Com SuperStack 3 Switch 3800 Family Скачать руководство пользователя страница 50

3-14

C

HAPTER

 3: A

CCESSING

 T

HE

 S

WITCH

Configuring

Autonegotiation

By default, the Switch 3800 is configured to use autonegotiation for all 
ports. Autonegotiation on 10/100 Mbps ports is used to automatically 
determine speed and duplex settings. You can select to manually 
configure the duplex and speed settings of 10/100 Mbps ports. Manual 
configuration would be used when the remote device does not support 
autonegotiation or when an interoperability issue exists.

The Switch 3800 Gigabit Ethernet port only supports a speed of 1,000 
Mbps and full duplex. Even though these parameters are fixed, 
autonegotiation on Gigabit links still allows proper link initialization and 
should be used whenever possible. Manual configuration would be 
used when the remote device does not support autonegotiation or 
when an interoperability issue exists.

10/100 port settings

Fast Ethernet ports can connect to either 10BASE-T or 100BASE-TX 
networks. By default, the ports autonegotiate port speed and duplex 
settings. You can manually determine these settings by turning 
autonegotiation off and providing speed and duplex settings. To 
configure port speed and duplex settings on 10/100 Mbps ports, use 
the following command:

config port <portlist> auto off (speed [10 | 100]} duplex 

[half | full]

To restore autonegotiation, use the following command:

config port <portlist> auto on

Gigabit port settings

By default the Gigabit port on the Switch 3800 uses autonegotiation to 
establish proper link initialization. Speed and duplex settings cannot be 
modified. To turn off autonegotiation, use the following command:

config port <portlist> auto off duplex full

The duplex setting must be provided even though the duplex setting 
may not be modified. To restore autonegotiation, use the following 
command:

config port <portlist> auto on

SW3800.BK  Page 14  Tuesday, May 5, 1998  5:20 PM

Содержание 3Com SuperStack 3 Switch 3800 Family























































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды