manualshive.com logo in svg

3Com 3Com SuperStack 3 Switch 3800 Family, Руководство пользователя

Поделиться
Скачать
3Com 3Com SuperStack 3 Switch 3800 Family Скачать руководство пользователя страница 89

Configuring VLANs on the Switch 3800

5-11

The Default VLAN

The Switch 3800 ships with one default VLAN that has the following 
properties:

■

The VLAN name is 

default.

■

It contains all the ports on a new or initialized Switch.

■

The default VLAN is untagged, and has no VLANid or protocol filter 
assigned. 

Configuring VLANs 
on the Switch 3800

This section describes the commands associated with setting up VLANs 
on the Switch 3800. Configuring a VLAN involves the following steps:

1

Create and name the VLAN.

2

Assign an IP address and subnet mask (if applicable) to the VLAN, if 
needed.

3

Assign a VLANid, if any ports in this VLAN will use a tag.

4

Assign one or more ports to the VLAN.

As you add each port to the VLAN, decide if the port will use an 
802.1Q tag.

SW3800.BK  Page 11  Tuesday, May 5, 1998  5:20 PM

Содержание 3Com SuperStack 3 Switch 3800 Family























































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды