manualshive.com logo in svg

3Com 3Com SuperStack 3 Switch 3800 Family, Руководство пользователя

Поделиться
Скачать
3Com 3Com SuperStack 3 Switch 3800 Family Скачать руководство пользователя страница 176

4

G

LOSSARY

on a wide range of computers and networking equipment and may be 
used to manage many aspects of network and endstation operation.

Spanning Tree

Protocol (STP)

A bridge-based mechanism for providing fault tolerance on networks. 
STP works by allowing the implementation of parallel paths for network 
traffic, and ensuring that redundant paths are disabled when the main 
paths are operational and enabled if the main paths fail.

switch

A device that filters, forwards, and floods frames based on the frame’s 
destination address. The Switch learns the addresses associated with 
each Switch port and builds tables based on this information to be 
used for the switching decision.

TCP/IP

A layered set of communications protocols providing Telnet terminal 
emulation, FTP file transfer, and other services for communication 
among a wide range of computer equipment.

Telnet

A TCP/IP application protocol that provides virtual terminal service, 
letting a user log in to another computer system and access a host as if 
the user were connected directly to the host.

TFTP

Trivial File Transfer Protocol that allows the transfer of files (such as 
software upgrades) from a remote device using the Switch’s local 
management capabilities.

Transcend

3Com’s umbrella management system used to manage all of 3Com’s 
networking solutions.

trap

A message sent by an SNMP agent to an authorized trap receiver 
(usually a network management station) to indicate the occurrence of a 
significant event, such as an error condition or a threshold that has 
been reached. 

UDP

User Datagram Protocol that is an Internet standard protocol allowing 
an application program on one device to send a datagram to an 
application program on another device.

VLAN

Virtual LAN that is a group of location- and topology-independent 
devices that communicate as if they are on a common physical LAN.

SW3800.BK  Page 4  Tuesday, May 5, 1998  5:20 PM

Содержание 3Com SuperStack 3 Switch 3800 Family























































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды