Zycoo ZP502 Page 24 User Manual Download

Page: 24 / 58

ZP502 User Manual

QoS Configuration

Field name

explanation

VLAN Enable

Before select it to enable VLAN, you need enable Bridge mode in

LAN config.

VLAN ID Check Enable

Enable VLAN ID check by selecting it. After enable VLAN ID

check, if VLAN ID of a data package is not the same with the

phone’s or a data package do not have VLAN ID, the data package

will be discarded.

Voice/Data VLAN

differentiated

After enable VLAN, system will set packets with different type of

VLAN ID. Undifferentiated means after using VLAN, both VoIP

packets and other data packets will use the voice VLAN ID; tag

differentiated means after using VLAN, VoIP(signal and voice)

packets will add voice VLAN ID, and other data packets will add

data VLAN ID; data untagged means after using VLAN, only VoIP

packets will add voice VLAN ID. Other data packets will not use

VLAN.

DiffServ Enable

Select it or not to Enable or disable DiffServ.

DiffServ Value

Set DiffServ value, the common value is 0x00.

Voice 802.1P Priority

Specify 802.1P Priority of voice/signal data package.

Data 802.1P Priority

Set 802.1p of data VLAN. Non-VoIP data (such as http, telnet, ping

etc) will use this value to set VLAN package.

Voice VLAN ID

Set VLAN ID of voice/signal data package.

Data VLAN ID

Set 802.1q of data VLAN ID. Non-VoIP data (such as http, telnet,

ping etc) will use this value to set VLAN package.

NOTICE

：

）

Startup VLAN, if set Voice/Data VLAN differentiated as Undifferentiated, all packets will

use the Voice VLAN ID as the tag.

2) Startup VLAN, if set Voice/Data VLAN differentiated as tag differentiated and disables the

DiffServ, then system will not distinguish the voice and data, all packets will use the Voice

VLAN ID as the tag.

3) Startup VLAN, if set Voice/Data VLAN differentiated as tag differentiated and enables the

DiffServ, then system will distinguish the voice and data and add the VLAN ID each other.

4) Startup VLAN, if set Voice/Data VLAN differentiated as data untagged, then the packet of

Summary of Contents for ZP502



























































Search results

Summary of Contents for ZP502

Reviews:

Related manuals for ZP502

Brands by name

Popular brands

Zycoo ZP502, User Manual

Search results

Summary of Contents for ZP502

Reviews:

Related manuals for ZP502

Brands by name

Popular brands