Zycoo ZP502 User Manual Download

Page: 37 / 58

ZP502 User Manual

You need set Phone Number,

Alias and Delete Length. Phone

number is XXXT and Alias is

rep:xxx

If your dialed phone number

starts with your set phone

number, the first digits same as

your set phone number will be

replaced by the alias number

specified

and

New

phone

number will be send out.

When

you

dial

“0106228”, the SIP1

server will receive

“0086106228”

If your dialed phone number

starts with your set phone

number. The phone will send

out your dialed phone number

adding suffix number.

When you dial “147”,

the SIP1 server will

receive “1470011”

4.3.4. Phone

4.3.4.1. DSP Config

In this page, you can configure voice codec, input/output volume and so on.

DSP Configuration

Field name

explanation

First Codec

The fist preferential DSP codec: G.711A/u, G.722, G.723, G.729

Second Codec

The second preferential DSP codec: G.711A/u, G.722, G.723, G.729

Third Codec

The third preferential DSP codec: G.711A/u, G.722, G.723, G.729

Forth Codec

The forth preferential DSP codec: G.711A/u, G.722, G.723, G.729

Summary of Contents for ZP502



























































Search results

Summary of Contents for ZP502

Reviews:

Related manuals for ZP502

Brands by name

Popular brands

Zycoo ZP502, User Manual

Search results

Summary of Contents for ZP502

Reviews:

Related manuals for ZP502

Brands by name

Popular brands