Zycoo ZP502 Page 53 User Manual Download

Page: 53 / 58

ZP502 User Manual

Notice:

After finish setting, click the Add button to add new mapping table; click the Delete

button to delete the selected mapping table.

Shows the outside WAN port IP address and the inside LAN port IP address.

Outside IP

Set the outside Wan port IP address of DMZ.

Inside IP

Set the inside LAN port IP address of DMZ

Click the

Add

button to add new table; click the

Delete

button to delete the selected mapping

table.

Notice:

10M/100M adaptive means the network card, and other equipment physical consultations

speed, testing speed under bridge mode near to 100M, in order to ensure the quality of voice and

communications real-time performance, we made some sacrifices of NAT under the transmission

performance. T

ransmit with full capability only when system is idle, so can not guarantee that the

transmission speed reach to 100M.

4.3.6.4. VPN Config

This web page provides us a safe connect mode by which we can make remote access to enterprise

inner network from public network. That is to say, you can set it to connect public networks in

different areas into inner network via a special tunnel.

Summary of Contents for ZP502



























































Search results

Summary of Contents for ZP502

Reviews:

Related manuals for ZP502

Brands by name

Popular brands

Zycoo ZP502, User Manual

Search results

Summary of Contents for ZP502

Reviews:

Related manuals for ZP502

Brands by name

Popular brands