background image

64

ZIP2 User’s Manual

B.4.2

Network Configuration Parameters

Network Configuration parameters define settings required by the phone to communicate with

the network. Figure B-4 lists the Network Configuration parameters.

Parameter

Description

Equivalent 
web interface 
parameter

Version 
Introduced

IF0DHCP

When set to’ DHCP’, phone uses DHCP to 

configure network settings: IP address, subnet 

mask, domain name, default gateway, DNS 

servers, NTP server address, and TFTP server 

address. Valid settings are ‘DHCP’ and 

‘FIXED’:
‘DHCP’ - enables DHCP
‘FIXED’ - disables DHCP and enables Fixed IP 

Addressing
Default value is ‘DHCP’.

section 5.3.2 on 

page 23

3.35

IF0DNSDOMAINNAME

Parameter is name of the domain in which the 

phone resides; used for manual configuration 

when IF0DHCP is set to ‘FIXED’ or DHCP 

does not return the domain (DHCP option 

15). Valid settings are FQDN or IP address in 

dotted decimal notation.
Default value is an empty string.

section 5.3.2 on 

page 23

3.35

IF0DNSHOSTNAME

Parameter is name of the FQDN of the host; 

used for manual configuration when 

IF0DHCP is set to ‘FIXED’ or DHCP does not 

return the host name (DHCP option 12). Valid 

setting is an FQDN.
Default value is an empty string.

section 5.3.2 on 

page 23

3.35

IF0IPADDRESS

Parameter is static address assigned to the 

ZIP2. Used for manual configuration when 

IF0DHCP is set to ‘FIXED’ or DHCP does not 

return an address (DHCP option 50). Valid 

setting is an IP address in dotted decimal 

notation.
Default value is an empty string.

section 5.3.2 on 

page 23

3.35

IF0IPDNS

Parameter is IP address of primary DNS 

Server. Used for manual configuration when 

IF0DHCP is set to ‘FIXED’ or DHCP does not 

return DNS Server (DHCP option 6). Valid 

setting is an IP address in dotted decimal 

notation.
Default value is an empty string.

section 5.3.2 on 

page 23

3.35

Figure B-4

Network Configuration Parameters

Summary of Contents for ZIP2



































































































Reviews: