ZOE PPM3 User Manual Download Page 172

Page: 172 / 214

18-2

N i g h t i n g a l e P P M 3 U s e r ' s G u i d e

April 2019

Troubleshooting

Trouble Symptom

Possible Causes

Things to Try

No patient name appears on the
PPM3

Patient Information has not been
entered into a standalone PPM3.

Supply the information in the
Setup Patient Information menu.

No connection to MPC

Verify the PPM3 is powered on,
the Network Cable is securely
connected to the PPM3 and the
wall plate labeled "Nightingale
Monitoring System"

Patient has not been admitted at the
MPC

Verify that the patient is admitted
at the MPC

The patient name on the PPM3
does not match the name on the
MPC

The patient was admitted to the
wrong small view area on the MPC

Verify that the patient is admitted
into the correct small view area
for the PPM3

The connection cabling to the PPM3
has been changed in the
telecommunications closet

Stop using the PPM3, contact Zoe
Medical Technical Support to re-
check the system installation

The PPM3 front panel keypad is
not working right

Keypad failure

Stop using the PPM3, contact Zoe
Medical Technical Support to
request a repair or replacement

The PPM3 knob is not working
right

Knob failure

Stop using the PPM3, contact Zoe
Medical Technical Support to
request a repair or replacement

The PPM3 display is not working
right

Display failure

Stop using the PPM3, contact Zoe
Medical Technical Support to
request a repair or replacement

The PPM3 is not working right
and displays an error message

Operating system failure

Power cycle the PPM3

– if

condition persists, stop using the
PPM3, contact Zoe Medical
Technical Support to request a
repair or replacement

The PPM3 displays a message
stating that the disk is too full.

The PPM3’s disk is too full and needs
to be cleaned up.

Stop using the PPM3, contact Zoe
Medical Technical Support to
request a repair or replacement

The PPM3 displays a message
stating that the CPU is too busy.

Internal system failure

Stop using the PPM3, contact Zoe
Medical Technical Support to
request a repair or replacement

Recorder problem detected

(Recorder option only)

Recorder is disconnected, or monitor
has sensed an error condition in the
recorder.

Check to be sure the recorder is
still connected.

If this does not help, stop using
the recorder, and contact Zoe
Medical Technical Support to
request a repair or replacement

Summary of Contents for PPM3























































































































































































































Search results

Summary of Contents for PPM3

Reviews:

Related manuals for PPM3

Brands by name

Popular brands

ZOE PPM3, User Manual

Search results

Summary of Contents for PPM3

Reviews:

Related manuals for PPM3

Brands by name

Popular brands