ZOE PPM3 User Manual Download Page 60

Page: 60 / 214

5-4

N i g h t i n g a l e P P M 3 U s e r ' s G u i d e

April 2019

Pulse Oximetry Monitoring

Note

– The SpO

waveform is not proportional to pulse volume.

Note

–

The accuracy of a pulse oximeter probe or a pulse oximeter monitor cannot be

assessed with a functional tester. The accuracy of the SpO

parameter in the Nightingale

PPM3 has been validated with a co-oximeter per ISO 80601-2-61.

5.4. Pediatric Considerations

It is important to select a SpO

sensor that is appropriate for the weight of the

patient. For example, a clean pulse oximetry waveform may not be obtainable
when an adult sensor is used on a small child. Weight-range information can be
found in the packaging that comes with the SpO

sensor.

Summary of Contents for PPM3























































































































































































































Search results

Summary of Contents for PPM3

Reviews:

Related manuals for PPM3

Brands by name

Popular brands

ZOE PPM3, User Manual

Search results

Summary of Contents for PPM3

Reviews:

Related manuals for PPM3

Brands by name

Popular brands