ZOE PPM3 User Manual Download Page 132

Page: 132 / 214

11-32

N i g h t i n g a l e P P M 3 U s e r ' s G u i d e

April 2019

Working With Menus

The Setup System Menu allows changes to a few items that are rarely changed.

Figure 57. Setup System Menu

The settings that can be changed via the Setup System menu include:

Setting

Description

Temp Units

Allows you to choose °F or °C

Height Units

Allows you to choose inches (in) or centimeters (cm)

Weight Units

Allows you to choose pounds (lb) or kilograms (kg)

Print Location

When connecting to the MPC, allows you to specify where
hard copy reports are printed (Bedside Only, Central Only,
Bedside And Central)

NOTE

– When a communications link with the MPC is established, these Units settings

will be overridden by those received from the MPC.

Summary of Contents for PPM3























































































































































































































Search results

Summary of Contents for PPM3

Reviews:

Related manuals for PPM3

Brands by name

Popular brands

ZOE PPM3, User Manual

Search results

Summary of Contents for PPM3

Reviews:

Related manuals for PPM3

Brands by name

Popular brands