background image

 

OPERATION 

Colibri 7  

Controlling the Colibri 7 solid-state light source  

ZEISS 

 

 
 

02/2017 

423052-7344-001 

29 

4.2.3.2

 

Control of Colibri 7 with the 

"Channels" tool in the 
"Acquisition" tab 

 

Click on the 

Acquisition

  tab in the software 

(see Fig. 19). 

 

Open the 

Channels

  tool by clicking on the 

expander  . 

 

Set the channels manually or via Smart Setup. 
Alternatively, you can load a saved experiment. 

 

If required, activate the 

Show All

 option. 

 

If required, select Colibri 7 as light source in 

Selected Lightsource

 

Switch the LEDs on or off by activating / 
deactivating the respective checkbox, e.g. 

 

Adjust the brightness for the selected wave 
length using the sliders, entry fields or arrow 

buttons. 

 

Activate the excitation filter for LED 567 by 
clicking on the 

555

 or 

590

 button at 

Excitation 

filter for LED 567

 

Select all LEDs simultaneously by clicking on 

Deactivate all LEDs 

or 

Activate all LEDs

 

Click on 

Continuous 

or 

Gated

  to select the 

desired mode for image acquisition.  

 

Image acquisition in "Continuous" mode in 

the "Acquisition" tab 
Continuous

  is the default setting for Colibri 7 in 

the ZEN control software.  
The camera and Colibri 7 are automatically 

controlled via software commands. Manual 
switching on or off is not necessary. 
Image acquisition during the experiment: The LEDs 
are shuttered between exposures via software 

commands. 

 

Select the required LEDs by clicking the 
corresponding checkbox and set the desired 

brightness.  

 

Use the 

Live

Continuous

 or 

Snap

 buttons to 

acquire images. 

 

 

Fig. 19 

Colibri 7 control via "Channels" tool 

 

Summary of Contents for Colibri 7



































Reviews: