Z3 Technology FSDI-DCK-1X Page 72 User Manual Download

Page: 72 / 87

FSDI-DCK-1X User Instructions

DOC-USR-0131-03

______________________________________________________________________________________

Z3 Technology, LLC

♦

100 N 8

ST, STE 250

♦

Lincoln, NE 68508-1369 USA

♦

+1.402.323.0702

Rtp Port (RTP Only)

0 – 9999 (

8700

)

Destination port for RTP audio.

Pid

(UDP/TSRTP/TSFILE

Only)

0 – 8191

(120)

Audio PID for transport stream.

Max PTS-PCR

(UDP/TSRTP/TSFILE

Only)

0 – 8191

(250)

Maximum difference between the PTS and PCR in the

audio stream. It is generally recommended to leave this

value at 250. Certain decoders may require a value similar

to the video delay. If an issue is encountered with a

specific decoder, try setting this value to the same value

as the video delay.

Output Setup

Output Format

RTP

RTSP

UDP

TSRTP

TSFILE

RTMP

Output format of the encoded IP stream.

If UDP is selected, don’t forget to check the value of TS

Rate to make sure it is in line with expectation.

RTP requires an SDP file for the receiver that corresponds

with the video codec used.

RTSP requires the use of the RTSP URL.

TSRTP causes streaming of TS over RTP. This format is

required for encoding with Pro-MPEG Forward Error

Correction (FEC).

RTMP is only supported with H264(AVC) selected as the

Video Codec.

Summary of Contents for FSDI-DCK-1X
























































































Search results

Summary of Contents for FSDI-DCK-1X

Reviews:

Related manuals for FSDI-DCK-1X

Brands by name

Popular brands

Z3 Technology FSDI-DCK-1X, User Manual

Search results

Summary of Contents for FSDI-DCK-1X

Reviews:

Related manuals for FSDI-DCK-1X

Brands by name

Popular brands