Z3 Technology FSDI-DCK-1X Page 43 User Manual Download

Page: 43 / 87

FSDI-DCK-1X User Instructions

DOC-USR-0131-03

______________________________________________________________________________________

Z3 Technology, LLC

♦

100 N 8

ST, STE 250

♦

Lincoln, NE 68508-1369 USA

♦

+1.402.323.0702

7.3

Color Controls

(4)

Select from a variety of supported white balance configurations using the

White Balance Mode

dropdown menu.

(5)

Adjust

Color Gain

and

Color Hue

using the sliders.

(6)

Use the button options to adjust to your desired

Color Suppress

settings.

7.4

Sony VISCA Camera Control

The FSDI-DCK-1X leverages Sony camera technology. Remote control of the camera video input is

supported by Sony’s VISCA™ protocol. VISCA commands can be sent from a remote PC using the same IP

connection that carries the video. Control actions include zoom, focus, aperture and more.

To complete the following instructions, a Windows 7 PC with Com2TCP

and your camera controller

software downloaded is required.

7.4.1

Com2TCP Setup

(1)

If you have not already done so, install the Com2TCP application onto your PC. (Windows 7 is

recommended. For Windows 8 or 10, verify you are using v1.4.6.) Com2TCP is an application

supporting remote access and is available online.

(2)

Launch the Com2TCP application.

Com2TCP is an application available for download online that allows for remote control of any serial device via IP.

Figure 45 Color Controls

Summary of Contents for FSDI-DCK-1X
























































































Search results

Summary of Contents for FSDI-DCK-1X

Reviews:

Related manuals for FSDI-DCK-1X

Brands by name

Popular brands

Z3 Technology FSDI-DCK-1X, User Manual

Search results

Summary of Contents for FSDI-DCK-1X

Reviews:

Related manuals for FSDI-DCK-1X

Brands by name

Popular brands