Z3 Technology FSDI-DCK-1X User Manual Download

Page: 63 / 87

FSDI-

DCK-

User Instructions

DOC-USR-0131-03

______________________________________________________________________________________

Z3 Technology, LLC

♦

100 N 8

ST, STE 250

♦

Lincoln, NE 68508-1369 USA

♦

+1.402.323.0702

SNTP Servers

(128.138.141.172)

Address of desired server for SNTP.

Set HTTP/HTTPS

Sets HTTP/HTTPS access to the web UI. See App Note for

more information

Set 802.1X

Sets configuration for 802.1x on the wired connection. See

App Note for details.

Configure FPGA*

Configures FPGA config for DCK-

XX unit. Z3 ships DCK units

with expected FPGA config, but changes to the hardware

configuration of

DCK may require a change to the FPGA

config. Most customers will not need change this setting.

Configure

ONVIF*

Enable/Disable ONVIF and contorl number of cameras to

advertise to ONVIF clients.

Set Term Server

Enable/Disable remote terminal server.

Set ZFinder

Enable/Disable ZFinder support on unit.

Update device

firmware Button

Access the Software Updater to update the firmware on

your device. An image file of the desired firmware is

needed.

Download

support logs

Button

Extract a set of diagnos

tic logs that can be provided to Z3

in the event of an issue to be reported. The resulting file is

saved on the PC with the user interface open.

Reboot Button

Restarts the unit without the need to disconnect power.

10.2

The

User Presets Tab

Button

Notes

new

Define a new configuration file.

Up to nine configurations can be created.

rename Rename a configuration file.

delete

Delete a configuration file.

export

Export current settings to a file.

import

Load settings from a previously exported file.

Reset

Resets presets

Summary of Contents for FSDI-DCK-1X
























































































Search results

Summary of Contents for FSDI-DCK-1X

Reviews:

Related manuals for FSDI-DCK-1X

Brands by name

Popular brands

Z3 Technology FSDI-DCK-1X, User Manual

Search results

Summary of Contents for FSDI-DCK-1X

Reviews:

Related manuals for FSDI-DCK-1X

Brands by name

Popular brands