Z3 Technology FSDI-DCK-1X Page 16 User Manual Download

Page: 16 / 87

FSDI-DCK-1X User Instructions

DOC-USR-0131-03

______________________________________________________________________________________

Z3 Technology, LLC

♦

100 N 8

ST, STE 250

♦

Lincoln, NE 68508-1369 USA

♦

+1.402.323.0702

6.0

STREAMING CONTROL

This section gives step-by-step instructions on setting the FSDI-DCK-1X to output and stream video using

each of the output format options: UDP, RTP, RTSP and RTMP. In addition to the FSDI-DCK-1X, a Windows PC

with the VLC media player

downloaded is required. Please see Section 8.4, Decoder Options, for more

information on compatible decoders and PC configuration and requirements for H.265/HEVC decode at HD

resolutions.

6.1

Stream UDP

6.1.1

UDP Camera Setup

Note:

Settings in the user interface cannot be changed if the unit is currently encoding.

(1)

If necessary, click on the

Stop

button in the

Channel Controls

section of the user interface CH1 tab

or the

Stop All

button in the lower right corner of the screen of any tab.

(2)

Verify the

Output Resolution

is set to

Follow Input

to output a HD stream. If a lower resolution

output is desired, select this in the dropdown menu and resizing will occur.

(3)

Select the

Video Codec

you would like to use for your video encoding. In the pictured example

H265(HEVC)

is selected.

(4)

Under Output Setup, select

UDP

in the

Output Format

dropdown menu.

(5)

Set Dest Address to:

the IP address of your PC that will be running the VLC media player. To determine the correct

IP address of your PC, see APPENDIX A: Finding the IP Address of Your Computer. In the

example pictured, 192.168.0.6 is used.

or a multicast address. An example multicast address would be 225.1.2.3. If you are on a

shared network, check with your Network Administrator.

(6)

Make note of the value listed for

Dest Port

. This will be

8600

by default when your system is first

received.

Note:

By default a limited selection of video encoding settings are available in the user interface. See Section

8.2, “Advanced Settings Mode”, for more information on accessing additional settings.

VLC is an open source media player from the VideoLAN organization that can be downloaded for free online.

Summary of Contents for FSDI-DCK-1X
























































































Search results

Summary of Contents for FSDI-DCK-1X

Reviews:

Related manuals for FSDI-DCK-1X

Brands by name

Popular brands

Z3 Technology FSDI-DCK-1X, User Manual

Search results

Summary of Contents for FSDI-DCK-1X

Reviews:

Related manuals for FSDI-DCK-1X

Brands by name

Popular brands