Z3 Technology FSDI-DCK-1X Page 11 User Manual Download

Page: 11 / 87

FSDI-DCK-1X User Instructions

DOC-USR-0131-03

______________________________________________________________________________________

Z3 Technology, LLC

♦

100 N 8

ST, STE 250

♦

Lincoln, NE 68508-1369 USA

♦

+1.402.323.0702

5.0

GETTING STARTED WITH THE FSDI-DCK-1X

WARNING: Use ONLY FCB-EV7520 or compatible camera with the FSDI-DCK-1X. Using an incompatible

camera may permanently damage the camera and the FSDI-DCK-1X.

Figure 4 Camera Compatibility Warning

Figure 5 FSDI-DCK-1X Physical Block Diagram (Cameras Not Included)

(1)

Once received, the FSDI-DCK-1X assembly will need to be connected to a SDI camera ( or the Sony

FCB-

EV7520 HD camera block) and the secondary camera with Composite Out. The Interface Front

End PCB of the FSDI-DCK-1X assembly (see Figure 7) has SDI input or 30-pin KEL connectors that

allow a flexible ribbon cable to be used to connect the encoder assembly to an identical connector

on the Sony FCB-EV7250. The Composite Out secondary camera is connected to the FSDI-DCK-1X

assembly via the MMCX or Flex I/O Connector (see Figure 6 8). The KEL cable (ordering part number:

SDI Camera

BNC

Summary of Contents for FSDI-DCK-1X
























































































Search results

Summary of Contents for FSDI-DCK-1X

Reviews:

Related manuals for FSDI-DCK-1X

Brands by name

Popular brands

Z3 Technology FSDI-DCK-1X, User Manual

Search results

Summary of Contents for FSDI-DCK-1X

Reviews:

Related manuals for FSDI-DCK-1X

Brands by name

Popular brands