6-6
IM DLM3054-03EN
Item
Specifications
Timeout:
Triggers when the pulse width of a single trigger source exceeds the set time
The source can be selected from CH1 to CH4
1
and LOGIC.
2
This is the same as Timeout of the Pulse Width trigger.
For details on the time settings, see “Pulse Width.”
Window:
Triggers when the window conditions of a single trigger source are met.
The source can be selected from CH1 to CH4.
1
Triggers when the source enters or exits from the voltage span set with the
upper and lower levels.
Further, triggers can be activated on the time that the source remains inside or
outside the voltage span.
The time condition can be set to None, More than, Less than, Inside, Outside,
or Timeout.
For details on the time settings, see “Pulse Width.”
Window OR:
Triggers on the OR of the window conditions of multiple trigger sources.
The source can be selected from CH1 to CH4.
1
Triggers when the source enters or exits from the voltage span set with the
upper and lower levels of each channel. Enter or exist can be set separately
for each source.
Interval:
Triggers on the time from the rising to the falling edge or the time from the
falling to the rising edge of a single trigger source.
The source can be selected from CH1 to CH4
1
and LOGIC.
2
The time condition can be set to None, More than, Less than, Inside, Outside,
or Timeout.
For details on the time settings, see “Pulse Width.”
FlexRay
4
:
Triggers on a FlexRay bus signal
The source can be set to a signal from CH1 to CH4.
Mode:
Frame Start, Error, ID/Data, ID OR
Bit Rate: 2.5M, 5M, 10Mbps
Bus channel: A, B
CAN
4
:
Triggers on a CAN (Controller Area Network) bus signal
The source can be set to a signal from CH1 to CH4.
Mode:
SOF, Error, ID/Data, ID OR
Bit Rate: 33.3k, 83.3k, 125k, 250k, 500k, 1Mbps, or User Define
For User Define, you can set a value from 10 k to 1 Mbps in 0.1 kbps
steps.
CAN FD
4
:
Triggers on a CAN FD (CAN with Flexible Data-Rate) bus signal (ISO or non-
ISO)
The source can be set to a signal from CH1 to CH4.
Mode:
SOF, Error, ID/Data, ID OR, EDF, ESI
Bit Rate: Arbitration phase
250k, 500k, 1Mbps, or User Define
For User Define, you can set a value from 20 k to 1 Mbps in 0.1-kbps
steps.
Data phase
500kbps, 1Mbps, 2Mbps, 4Mbps, 5Mbps, 8Mbps
or User Define
For User Define, you can set a value from 250 k to 10 Mbps in 0.1-
kbps steps.
LIN
4
:
Triggers on a LIN (Local Interconnect Network) bus signal
The source can be set to a signal from CH1 to CH4.
Mode:
Break Synch, Error, ID/Data, ID OR
Bit Rate: 1200, 2400, 4800, 9600, 19200bps, or User Define
For User Define, you can set a value from 1 k to 20 kbps in 0.01-kbps
steps.
CXPI
4
:
Triggers on a CXPI (Clock Extension Peripheral Interface) bus signal
The source can be set to a signal from CH1 to CH4.
Mode:
SOF, Error, PTYPE, ID/Data, ID OR, Wakeup/Sleep
Bit Rate: 4800, 9600, 19200bps, or User Define
For User Define, you can set a value from 4 k to 50 kbps in 0.01-kbps
steps.
SENT
4
:
Triggers on SENT signals (J2716 JAN2010 and earlier)
The source can be selected from CH1 to CH4 and LOGIC.
2
Mode:
Every Fast CH, Fast CH S&C (Status & Communication),
Fast CH Data, Every Slow CH, Slow CH ID/Data, Error
Clock period: 1 µs to 100 µs (0.01µs resolution)
6.2 Triggering Section
