Yamatake HGC303 User Manual Download Page 33

Page: 33 / 130

Yamatake Corporation

Installation

Model HGC303 - Heat Value Gas Chromatograph

2-13

Terminators

A terminator is an impedance matching module used near or at the end of a transmis-
sion line. Terminators prevent distortion and signal loss.

A terminator shall be located at both ends of a trunk cable, connected from one signal
conductor to the other.

A trunk is the longest cable path between any two devices on the fieldbus network.

ONLY TWO terminators are required per fieldbus segment.

No connection shall be made between the terminator and cable shield.

The terminator impedance value shall be 100 ohm +/- 2% over a frequency range of
7.8 kHz to 39 kHz.

The model HGC303 and model HMU303 have a terminator at the fieldbus connection
port therefore an additional terminator is not required.

Terminal blocks

The terminal blocks can be the same as those used for 4-20mA.

Connectors

D-sub 9P connector is as specified for standard fieldbus connectors in the IEC/ISA
Standard.

Contact No.

Signal

Data +

Data -

Summary of Contents for HGC303



































































































































Search results

Summary of Contents for HGC303

Reviews:

Related manuals for HGC303

Brands by name

Popular brands

Yamatake HGC303, User Manual

Search results

Summary of Contents for HGC303

Reviews:

Related manuals for HGC303

Brands by name

Popular brands