Yamatake HGC303 User Manual Download Page 104

Page: 104 / 130

Operation

Yamatake Corporation

3-62

Model HGC303 - Heat Value Gas Chromatograph

~Note

Description of calculated value (GPA)

Select one of the four items to view the calculated values (

BTU (dry),

BTU (sat),

Density,

GPM)

All calculated values for that item are then displayed.

The contents of the calculated values are given below.

BTU (dry)

BTU (sat)

Density

GPM

Refer to the appendix for the calculation formula for each value.

Total (raw) Total raw concentration

Total (raw)

Total raw concentration

Real GHV Real Gross Heating Value (dry)

Real GHV

Real Gross Heating Value (sat)

Real NHV Real Net Heating Value (dry)

Real NHV

Real Net Heating Value (sat)

GHM

Gross Heating Value per unit mass (dry)

Compressibility factor (sat

NHM

Net Heating Value per unit mass (dry)

Compressibility factor (dry)

Gas Density

GPM C2+

Gallon per 1000CF C2+

Liquid Density

GPM C3+

Gallon per 1000CF C3+

Real RD gas Real Relative Density, gas (dry)

GPM C4+

Gallon per 1000CF C4+

RD liquid

Relative Density, liquid

GPM iC5+

Gallon per 1000CF iC5+

Real WI (dry) Real Wobbe Index (dry)

RVP

Reid Vapor Pressure

Real WI (sat) Real Wobbe Index (sat)

Summary of Contents for HGC303



































































































































Search results

Summary of Contents for HGC303

Reviews:

Related manuals for HGC303

Brands by name

Popular brands

Yamatake HGC303, User Manual

Search results

Summary of Contents for HGC303

Reviews:

Related manuals for HGC303

Brands by name

Popular brands