Yamatake HGC303 User Manual Download Page 20

Page: 20 / 130

Introduction

Yamatake Corporation

1-6

Model HGC303 - Heat Value Gas Chromatograph

1-5 : Fieldbus communication system

The model HGC303 uses F

OUNDATION

™ fieldbus technology to transfer information

between other devices.

The F

OUNDATION

™ fieldbus is an open, 2-wire, multi-drop, two-way digital commu-

nication system which interconnects field equipment such as sensors, actuators and
controllers.

The F

OUNDATION

™ fieldbus is supported by a worldwide network of customers and

manufacturers in Europe, North America and Asia Pacific.

OUNDATION

™ fieldbus

http://www.fieldbus.org/

OUNDATION

™ fieldbus literature

(1) F

OUNDATION

™ fieldbus Technical overview (FD-043)

(2) Fieldbus Installation & Planning Guide (AG-165)

(3) F

OUNDATION

™ fieldbus Application Guide

31.25kbit/s Wiring and Installation (AG-140)

(4) F

OUNDATION

™ fieldbus Application Guide

31.25kbit/s Intrinsically Safe Systems (AG-163)

Summary of Contents for HGC303



































































































































Search results

Summary of Contents for HGC303

Reviews:

Related manuals for HGC303

Brands by name

Popular brands

Yamatake HGC303, User Manual

Search results

Summary of Contents for HGC303

Reviews:

Related manuals for HGC303

Brands by name

Popular brands