Yamatake HGC303 User Manual Download Page 56

Page: 56 / 130

Operation

Yamatake Corporation

3-14

Model HGC303 - Heat Value Gas Chromatograph

3-3-3 : HGM Main menu

The contents of the main menu are described in this section.

The screen shown below is displayed once the HGM is started up.

Figure 3-4 Main menu

The HGM main menu is divided into six functions

(OFFLINE)

(ONLINE)

Table 3-5 Main menu description

Display

Description

Offline (Online)

Displays the Online/Offline status.

Set up HGM

Select Online/Offline mode, Data saving interval.

User's Mode

Monitoring heat value trend graph and chromatogram.

You can also perform calibrations using this mode.

User's manual

Model HGC303 user's manual reference (pdf file).

Configuration mode

The model HGC303 can be configured from here can be

done here.

Quit

Exit from the HGM application.

Summary of Contents for HGC303



































































































































Search results

Summary of Contents for HGC303

Reviews:

Related manuals for HGC303

Brands by name

Popular brands

Yamatake HGC303, User Manual

Search results

Summary of Contents for HGC303

Reviews:

Related manuals for HGC303

Brands by name

Popular brands