Yamatake HGC303 User Manual Download Page 70

Page: 70 / 130

Operation

Yamatake Corporation

3-28

Model HGC303 - Heat Value Gas Chromatograph

3-3-7 : Report

To create a report, click on the [report] icon in the right panel of User's mode.

The following entry form for process gas data will appear.

Figure 3-12 User report entry form

Enter the necessary items and click on [Preview].

It is not necessary to fill out all of the boxes.

When online, the latest analysis data can be viewed by clicking on [report].

When offline, the report or chromatogram that you had saved will be displayed.

To print out a report, click on [Preview] then [print out].

~Note

File name extension of an user report is .cg1 (same as chromatogram).

~Note

When you want to save report data, save either the report or the

chromatogram.

The chromatogram file (.cg1) includes the report data.

HGM000020000S

Summary of Contents for HGC303



































































































































Search results

Summary of Contents for HGC303

Reviews:

Related manuals for HGC303

Brands by name

Popular brands

Yamatake HGC303, User Manual

Search results

Summary of Contents for HGC303

Reviews:

Related manuals for HGC303

Brands by name

Popular brands