Yamaha YZFR1W 2007 Service Manual Download

Page: 191 / 429

SWINGARM

4-69

NOTE:

Loosen the swingarm pivot shaft with the
damper rod holder (22 mm) “2”.

EAS23360

CHECKING THE SWINGARM

1. Check:

• Swingarm

Bends/cracks/damage

→

Replace.

2. Check:

• Pivot shaft

Roll the pivot shaft on a flat surface.
Bends

→

Replace.

WARNING

EWA13770

Do not attempt to straighten a bent pivot
shaft.

3. Wash:

• Pivot shaft
• Dust covers
• Spacer

• Washers
• Bearings

4. Check:

• Dust covers “1”
• Spacer “2”
• Washer “3”

Damage/wear

→

Replace.

• Bearings “4”

Damage/pitting

→

Replace.

EAS23380

INSTALLING THE SWINGARM

1. Lubricate:

• Bearings
• Spacers
• Dust covers
• Pivot shaft

2. Install:

• Bearing “1”
• Bearing “2”
• Washer “3”

Damper rod holder (22 mm)

90890-01365

Recommended cleaning solvent

Kerosene

Recommended lubricant

Molybdenum disulfide grease

Installed depth of bearing “a”

0–1.0 mm (0–0.04 in)

4. Dust cover

Summary of Contents for YZFR1W 2007














































































































































































































































































































































































































































Search results

Summary of Contents for YZFR1W 2007

Reviews:

Related manuals for YZFR1W 2007

Brands by name

Popular brands

Yamaha YZFR1W 2007, Service Manual

Search results

Summary of Contents for YZFR1W 2007

Reviews:

Related manuals for YZFR1W 2007

Brands by name

Popular brands