Yamaha YZFR1W 2007 Service Manual Download Page 267 | Manualshive

Page: 267 / 429

background image

CRANKCASE

5-67

EAS25550

DISASSEMBLING THE CRANKCASE

1. Place the engine upside down.
2. Remove:

• Crankcase bolts

NOTE:

• Loosen each bolt 1/4 of a turn at a time, in

stages and in a crisscross pattern. After all of
the bolts are fully loosened, remove them.

• Loosen the bolts in decreasing numerical

order (refer to the numbers in the illustration).

• The numbers embossed on the crankcase

indicate the crankcase tightening sequence.

M6

×

50 mm (2.0 in) bolts: “1”, “7”

M6

×

60 mm (2.4 in) bolts: “2”, “3”

M6

×

70 mm (2.8 in) bolts: “4”, “6”, “8”

M6

×

60 mm (2.4 in) bolt and washer: “5”

M6

×

65 mm (2.5 in) bolts: “9”, “10”

M8

×

60 mm (2.4 in) bolts: “11”, “15”

M8

×

50 mm (2.0 in) bolts: “12” – “14”

M8

×

60 mm (2.4 in) bolt: “16” LOCTITE®

M9

×

105 mm (4.1 in) bolts: “17” – “26”

3. Remove:

• Lower crankcase

CAUTION:

ECA13900

Tap on one side of the crankcase with a
soft-face hammer. Tap only on reinforced
portions of the crankcase, not on the
crankcase mating surfaces. Work slowly
and carefully and make sure the crankcase
halves separate evenly.

4. Remove:

• Dowel pins

5. Remove:

• Crankshaft journal lower bearing

(from the lower crankcase)

NOTE:

Identify the position of each crankshaft journal
lower bearing so that it can be reinstalled in its
original place.

EAS25580

CHECKING THE CRANKCASE

1. Thoroughly wash the crankcase halves in a

mild solvent.

2. Thoroughly clean all the gasket surfaces

and crankcase mating surfaces.

3. Check:

• Crankcase

Cracks/damage

→

Replace.

• Oil delivery passages

Obstruction

→

Blow out with compressed

air.

EAS4C81014

CHECKING THE BEARING AND OIL SEALS

1. Check:

• Bearings

Clean and lubricate the bearings, then
rotate the inner race with your finger.
Rough movement

→

Replace.

2. Check:

• Oil seals

Damage/wear

→

Replace.

EAS25650

ASSEMBLING THE CRANKCASE

1. Lubricate:

• Crankshaft journal bearings

(with the recommended lubricant)

2. Apply:

• Sealant

NOTE:

Do not allow any sealant to come into contact
with the oil gallery or crankshaft journal bear-
ings. Do not apply sealant to within 2–3 mm
(0.08–0.12 in) of the crankshaft journal bear-
ings.

Recommended lubricant

Engine oil

Yamaha bond No. 1215

(Three bond No. 1215®)
90890-85505

«
...
265
266
267
268
269
...
»

Summary of Contents for YZFR1W 2007














































































































































































































































































































































































































































Reviews:

No comments

Related manuals for YZFR1W 2007

Brand: GAS GAS Pages: 56

Brand: B-PWR Pages: 13

Brand: R&G Pages: 13

Brand: Nolan Pages: 24

Brand: Romet Pages: 52

V125 Special 2018

Brand: Lambretta Pages: 53

Brand: N-Com Pages: 2

Brand: Leatt Pages: 23

Compu-Fire 55120 32

Brand: PerTronix Pages: 3

Brand: EINHELL Pages: 48

Brand: hepco & becker Pages: 2

Brand: TM Pages: 80

Brand: Cobra Pages: 2

Brand: Shark Pages: 16

PHANTOM F 12 Liquid Cooled

Brand: Malaguti Pages: 16

Brand: RIEJU Pages: 78

Brand: R&G Pages: 23

Brand: Iron Rider Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands