Yamaha YZFR1W 2007 Service Manual Download Page 351 | Manualshive

Page: 351 / 429

background image

FUEL INJECTION SYSTEM

8-32

EAS27362

FAIL-SAFE ACTIONS (SUBSTITUTE CHARACTERISTICS OPERATION CONTROL)

If the ECU detects an abnormal signal from a sensor while the vehicle is being driven, the ECU illu-
minates the engine trouble warning light and provides the engine with alternate operating instruc-
tions that are appropriate for the type of malfunction.
When an abnormal signal is received from a sensor, the ECU processes the specified values that
are programmed for each sensor in order to provide the engine with alternate operating instructions
that enable the engine to continue to operate or stop operating, depending on the conditions.

Self-Diagnostic Function table

a. Main switch “OFF”
b. Main switch “ON”
c. Engine trouble warning light off
d. Engine trouble warning light on for 1.4 sec-

onds

Fault

code No.

Item

Symptom

Able /

unable to

start

Able /

unable to

drive

11

Cylinder identification
sensor

• No normal signals are received

from the cylinder identification
sensor.

• Malfunction of electric starting

system.

Unable

Able

12

Crankshaft position
sensor

No normal signals are received
from the crankshaft position sen-
sor.

Unable

Unable

13

Intake air pressure
sensor
(open or short circuit)

Intake air pressure sensor-open or
short circuit detected.

Able

Able

14

Intake air pressure
sensor
(pipe system)

Intake air pressure sensor-pipe
system malfunction (clogged or
detached hose).

Able

Able

15

Throttle position sen-
sor (for throttle valves)
(open or short circuit/
loose connection)

Throttle position sensor (for throttle
valves):
open or short circuit detected.
Throttle position sensor (for throttle
valves) coupler connection is
loose.

Able/Unable Able/Unable

17

EXUP servo motor cir-
cuit
(open or short circuit)

EXUP servo motor circuit: open or
short circuit detected.

Able

Able

18

EXUP servo motor
(stuck)

EXUP servo motor is stuck.

Able

Able

19

Sidestand switch
(open circuit wire har-
ness to ECU)

Open circuit is detected in the input
line from the sidestand switch to
the ECU.

Unable

Unable

«
...
349
350
351
352
353
...
»

Summary of Contents for YZFR1W 2007














































































































































































































































































































































































































































Reviews:

No comments

Related manuals for YZFR1W 2007

Brand: Yamaha Pages: 572

Brand: Yamaha Pages: 584

Brand: Yamaha Pages: 410

Brand: Yamaha Pages: 576

Brand: Yamaha Pages: 668

Brand: Yamaha Pages: 596

Brand: Yamaha Pages: 656

Brand: Yamaha Pages: 378

Brand: Sachs Bikes Pages: 71

Brand: R&G Pages: 4

Brand: Dakota Digital Pages: 6

Brand: BMW Pages: 176

CoreManual TorqDrive

Brand: Rekluse Pages: 20

Brand: Corbin Pages: 4

Brand: KTM Power Parts Pages: 12

Brand: hepco & becker Pages: 2

Brand: Bajaj Pages: 44

Brand: Surtek Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands