manualshive.com logo in svg

Yamaha YZFR1W 2007, Service Manual

The Yamaha YZFR1W 2007 Owner's Manual is a comprehensive guide for users of the powerful Yamaha YZFR1W motorcycle. Packed with essential information and detailed instructions, this manual is available for free download at manualshive.com. Discover the full potential of your bike with this reliable and user-friendly manual.

Share
Download
background image

PERIODIC CHECKS AND ADJUSTMENTS

PERIODIC MAINTENANCE

.........................................................................3-1

INTRODUCTION ....................................................................................3-1
PERIODIC MAINTENANCE CHART FOR THE EMISSION 
CONTROL SYSTEM...............................................................................3-1
GENERAL MAINTENANCE AND LUBRICATION CHART .....................3-1

ENGINE

.........................................................................................................3-4

ADJUSTING THE VALVE CLEARANCE ................................................3-4
SYNCHRONIZING THE THROTTLE BODIES .......................................3-7
ADJUSTING THE THROTTLE CABLE FREE PLAY ..............................3-8
CHECKING THE SPARK PLUGS...........................................................3-9
MEASURING THE COMPRESSION PRESSURE ............................... 3-10
CHECKING THE ENGINE OIL LEVEL ................................................. 3-11
CHANGING THE ENGINE OIL............................................................. 3-11
MEASURING THE ENGINE OIL PRESSURE ..................................... 3-13
ADJUSTING THE CLUTCH CABLE FREE PLAY ................................ 3-14
REPLACING THE AIR FILTER ELEMENT ........................................... 3-14
CHECKING THE THROTTLE BODY JOINTS ...................................... 3-15
CHECKING THE FUEL LINE ............................................................... 3-15
CHECKING THE CRANKCASE BREATHER HOSE ............................ 3-16
CHECKING THE EXHAUST SYSTEM ................................................. 3-16
ADJUSTING THE EXUP CABLES .......................................................3-17
CHECKING THE EXUP SERVO MOTOR............................................. 3-18
CHECKING THE COOLANT LEVEL .................................................... 3-18
CHECKING THE COOLING SYSTEM ................................................. 3-19
CHANGING THE COOLANT ................................................................ 3-19

CHASSIS

.................................................................................................... 3-22

ADJUSTING THE FRONT DISC BRAKE ............................................. 3-22
ADJUSTING THE REAR DISC BRAKE ............................................... 3-22
CHECKING THE BRAKE FLUID LEVEL .............................................. 3-23
CHECKING THE FRONT BRAKE PADS.............................................. 3-23
CHECKING THE REAR BRAKE PADS ................................................ 3-24
CHECKING THE FRONT BRAKE HOSES........................................... 3-24
CHECKING THE REAR BRAKE HOSE ............................................... 3-24
ADJUSTING THE REAR BRAKE LIGHT SWITCH .............................. 3-24
BLEEDING THE HYDRAULIC BRAKE SYSTEM ................................. 3-25
ADJUSTING THE SHIFT PEDAL ......................................................... 3-26
ADJUSTING THE DRIVE CHAIN SLACK ............................................ 3-26
LUBRICATING THE DRIVE CHAIN...................................................... 3-27
CHECKING AND ADJUSTING THE STEERING HEAD ...................... 3-27
CHECKING THE FRONT FORK .......................................................... 3-29
ADJUSTING THE FRONT FORK LEGS .............................................. 3-29
ADJUSTING THE REAR SHOCK ABSORBER ASSEMBLY................ 3-31
CHECKING THE TIRES ....................................................................... 3-32
CHECKING THE WHEELS .................................................................. 3-34
CHECKING AND LUBRICATING THE CABLES ..................................3-34
LUBRICATING THE LEVERS............................................................... 3-34
LUBRICATING THE PEDAL ................................................................. 3-35

Summary of Contents for YZFR1W 2007














































































































































































































































































































































































































































Reviews:

No comments

Related manuals for YZFR1W 2007

W-Tec Ondrejnik User Manual preview
Ondrejnik
Brand: W-Tec Pages: 6
R&G CP0443 Fitting Instructions Manual preview
CP0443
Brand: R&G Pages: 12
KYMCO PEOPLE S 125 Owner'S Manual preview
PEOPLE S 125
Brand: KYMCO Pages: 55
Honda 08L42-MCA-100 Installation Instructions preview
08L42-MCA-100
Brand: Honda Pages: 3
R&G CP0466 Series Fitting Instructions Manual preview
CP0466 Series
Brand: R&G Pages: 9
AMERICAN IRONHORSE Classic SX User Manual preview
Classic SX
Brand: AMERICAN IRONHORSE Pages: 104
Puch Magnum X Service Manual preview
Magnum X
Brand: Puch Pages: 151
Yamaha YZ250X 2022 Owner'S Service Manual preview
YZ250X 2022
Brand: Yamaha Pages: 276
hepco & becker 630338 00 02 Mounting Instructions preview
630338 00 02
Brand: hepco & becker Pages: 4
hepco & becker 6304554 00 01 Quick Start Manual preview
6304554 00 01
Brand: hepco & becker Pages: 4
Race Dynamics PowerTRONIC Installation Manual preview
PowerTRONIC
Brand: Race Dynamics Pages: 25
Protos Integral User Manual preview
Integral
Brand: Protos Pages: 6
RIEJU CENTURY 125IE Owner'S Manual preview
CENTURY 125IE
Brand: RIEJU Pages: 34
Baotian BT49QT-3 Service Manual preview
BT49QT-3
Brand: Baotian Pages: 30
Careflon CX-1 Owner'S Manual preview
CX-1
Brand: Careflon Pages: 16
Kriega US-DRYPACKS+ Fitting Instructions preview
US-DRYPACKS+
Brand: Kriega Pages: 2
hepco & becker 8006519 00 01 Quick Start Manual preview
8006519 00 01
Brand: hepco & becker Pages: 3
KTM 55103190000 Information preview
55103190000
Brand: KTM Pages: 7

Brands by name

Popular brands

Load more brands