Yamaha YZFR1W 2007 Service Manual Download Page 117 | Manualshive

Page: 117 / 429

background image

CHASSIS

3-34

WARNING

EWA14090

After extensive tests, the tires listed below
have been approved by Yamaha Motor Co.,
Ltd. for this model. The front and rear tires
should always be by the same manufac-
turer and of the same design. No guarantee
concerning handling characteristics can be
given if a tire combination other than one
approved by Yamaha is used on this vehi-
cle.

WARNING

EWA13210

New tires have a relatively low grip on the
road surface until they have been slightly
worn. Therefore, approximately 100 km
should be traveled at normal speed before
any high-speed riding is done.

NOTE:

For tires with a direction of rotation mark “1”:
• Install the tire with the mark pointing in the

direction of wheel rotation.

• Align the mark “2” with the valve installation

point.

EAS21670

CHECKING THE WHEELS

The following procedure applies to both of the
wheels.
1. Check:

• Wheel

Damage/out-of-round

→

Replace.

WARNING

EWA13260

Never attempt to make any repairs to the
wheel.

NOTE:

After a tire or wheel has been changed or
replaced, always balance the wheel.

EAS21690

CHECKING AND LUBRICATING THE
CABLES

The following procedure applies to all of the
inner and outer cables.

WARNING

EWA13270

Damaged outer cable may cause the cable
to corrode and interfere with its movement.
Replace damaged outer cable and inner
cables as soon as possible.

1. Check:

• Outer cable

Damage

→

Replace.

2. Check:

• Cable operation

Rough movement

→

Lubricate.

NOTE:

Hold the cable end upright and pour a few
drops of lubricant into the cable sheath or use
a suitable lubricating device.

EAS21700

LUBRICATING THE LEVERS

Lubricate the pivoting point and metal-to-metal
moving parts of the levers.

Front tire

Size

120/70 ZR17M/C (58W)

Manufacturer/model

PIRELLI/DIABLO CORSA E

Manufacturer/model

MICHELIN/Pilot POWER

Rear tire

Size

190/50 ZR17M/C (73W)

Manufacturer/model

PIRELLI/DIABLO CORSA L

Manufacturer/model

MICHELIN/Pilot POWER

Recommended lubricant

Engine oil or a suitable cable
lubricant

Recommended lubricant

Lithium-soap-based grease

«
...
115
116
117
118
119
...
»

Summary of Contents for YZFR1W 2007














































































































































































































































































































































































































































Reviews:

No comments

Related manuals for YZFR1W 2007

Brand: N-Com Pages: 2

Brand: N-Com Pages: 64

PAMPERA 400 - 2006

Brand: GAS GAS Pages: 70

Brand: Honda Pages: 100

Brand: FDC Pages: 6

TwinSpark Super head plus R

Brand: Takegawa Pages: 5

Brand: BMW Pages: 416

Brand: KTM Pages: 90

Brand: Öhlins Pages: 2

Brand: Yamaha Pages: 110

Brand: Hama Pages: 22

Brand: Athena Pages: 88

Brand: Enerwatt Pages: 26

Motorcycles 2006

Brand: RIDLEY Pages: 53

DORSODURO - 2009

Brand: APRILIA Pages: 9

Brand: Hobart Pages: 20

2014 1190 Adventure

Brand: KTM Pages: 228

Indian Challenger 2020

Brand: Indian Motorcycle Pages: 178

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands