Yamaha YZF-R1 2015 Service Manual Download Page 380

Page: 380 / 704

STARTER CLUTCH

5-39

EAS30305

REMOVING THE STARTER CLUTCH

1. Remove:

•

Starter clutch bolt “1”

TIP

•

While holding the clutch housing assembly “2”
with the sheave holder “3”, remove the starter
clutch bolt.

•

Fix the flat surface of the clutch housing as-
sembly with the sheave holder.

EAS30306

CHECKING THE STARTER CLUTCH

1. Check:

•

Starter clutch rollers “1”
Damage/wear

Replace.

2. Check:

•

Starter clutch gear “1”

•

Starter clutch idle gear “2”
Burrs/chips/roughness/wear

Replace the

defective part(s).

3. Check:

•

Starter clutch gear’s contacting surfaces
Damage/pitting/wear

Replace the starter

clutch gear.

4. Check:

•

Starter clutch operation

▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼

a. Install the starter clutch gear “1” onto the

clutch housing assembly “2” and hold the
clutch housing assembly.

b. When turning the starter clutch gear clock-

wise “A”, the starter clutch and the starter
clutch gear should engage, otherwise the
starter clutch is faulty and must be replaced.

c. When turning the starter clutch gear counter-

clockwise “B”, it should turn freely, otherwise
the starter clutch is faulty and must be re-
placed.

▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲

EAS30309

INSTALLING THE STARTER CLUTCH

1. Install:

•

Starter clutch

TIP

•

Install the starter clutch so that the side of the
starter clutch roller assembly with the arrow
mark is toward the clutch housing.

Sheave holder

90890-01701

Primary clutch holder

YS-01880-A

Starter clutch holder bolt

14 Nm (1.4 m·kgf, 10 ft·lbf)

LOCTITE®

Summary of Contents for YZF-R1 2015

































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for YZF-R1 2015

Reviews:

Related manuals for YZF-R1 2015

Brands by name

Popular brands

Yamaha YZF-R1 2015, Service Manual

Search results

Summary of Contents for YZF-R1 2015

Reviews:

Related manuals for YZF-R1 2015

Brands by name

Popular brands