Yamaha YZF-R1 2015 Service Manual Download Page 675

Page: 675 / 704

ELECTRICAL COMPONENTS

8-194

c. Turn the main switch to “ON”.
d. Rotate the crankshaft.
e. Measure the voltage. With each full rotation

of the crankshaft, the voltage reading should
cycle from 0.8 V to 4.8 V to 0.8 V to 4.8 V.

▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲

EAS30593

CHECKING THE INTAKE AIR PRESSURE

SENSOR

1. Check:

•

Intake air pressure sensor output voltage
Out of specification

Replace.

▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼

a. Connect the test harness S– pressure sensor

(3P) “1” to the intake air pressure sensor and
wire harness as shown.

NOTICE

ECA20920

Pay attention to the installing direction of the

test harness S– pressure sensor (3P) cou-

pler.

b. Connect the digital circuit tester (DCV) to the

test harness S– pressure sensor (3P).

c. Set the main switch to “ON”.
d. Measure the intake air pressure sensor out-

put voltage.

▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲

EAS30594

CHECKING THE INTAKE AIR

TEMPERATURE SENSOR

1. Remove:

•

Intake air temperature sensor

WARNING

EWA14110

• Handle the intake air temperature sensor

with special care.

• Never subject the intake air temperature

sensor to strong shocks. If the intake air

temperature sensor is dropped, replace it.

2. Check:

•

Intake air temperature sensor resistance
Out of specification

Replace.

Pocket tester

90890-03112

Analog pocket tester

YU-03112-C

Test harness– speed sensor (3P)

90890-03208

Test harness– speed sensor (3P)

YU-03208

•

Positive tester probe

white/black (wire harness color)

•

Negative tester probe

black/blue (wire harness color)

Intake air pressure sensor output

voltage

3.57–3.71 [email protected] kPa (3.57–

3.71 [email protected] kgf/cm², 3.57–3.71

[email protected] psi)

Digital circuit tester

90890-03174

Model 88 Multimeter with tachom-

eter

YU-A1927

Test harness S– pressure sensor

(3P)

90890-03207

Test harness S– pressure sensor

(3P)

YU-03207

•

Positive tester probe

pink/white (wire harness color)

•

Negative tester probe

black/blue (wire harness color)

Intake air temperature sensor re-

sistance

209–390

@80

C (176

Summary of Contents for YZF-R1 2015

































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for YZF-R1 2015

Reviews:

Related manuals for YZF-R1 2015

Brands by name

Popular brands

Yamaha YZF-R1 2015, Service Manual

Search results

Summary of Contents for YZF-R1 2015

Reviews:

Related manuals for YZF-R1 2015

Brands by name

Popular brands