Yamaha YZF-R1 2015 Service Manual Download Page 687

Page: 687 / 704

SELF-DIAGNOSTIC FUNCTION AND DIAGNOSTIC CODE TABLE

(ECU)

9-8

Accelerator position sensor

signal 2

•

Fully closed position

10–24

Check with throttle grip fully

closed position.

•

Fully open position

95–109

Check with throttle grip fully

open position.

Front wheel vehicle speed

pulses

Front wheel speed pulse

0–999

Check that the number

increases when the front

wheel is rotated. The number

is cumulative and does not

reset each time the wheel is

stopped.

Bank angle display

Displays the bank angle

increments of 5

•

0–5

(vehicle is vertical)

•

Less than 30

(when the

sidestand is used)

Check that 0–5

is displayed

when the vehicle is vertical

and that the displayed value

increases as the vehicle con-

tinues to incline.

Sidestand switch

Extend and retract the sides-

tand (with the transmission in

gear).

•

Sidestand retracted

•

Sidestand extended

OFF

Neutral switch and clutch

switch

Operate the transmission,

clutch lever, and sidestand.

•

Transmission is in neutral

•

Transmission is in gear or

the clutch lever released

OFF

•

Clutch lever is squeezed

with the transmission in

gear and when the sides-

tand is retracted

•

Clutch lever is squeezed

with the transmission in

gear and when the sides-

tand is extended

OFF

EEPROM fault code display

—

•

No history

•

No malfunctions detected

(If the self-diagnosis fault

code 44 is indicated, the

ECU is defective.)

•

History exists

01–04 (Cylinder fault code)

•

(If more than one cylinder is

defective, the display alter-

nates every two seconds to

show all the detected cylin-

der numbers.

When all cylinder numbers

are shown, the display

repeats the same process.)

11 (Data error for ISC (Idle

Speed Control) learning val-

ues)

Diagnostic

code No.

Item

Meter display

Procedure

Summary of Contents for YZF-R1 2015

































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for YZF-R1 2015

Reviews:

Related manuals for YZF-R1 2015

Brands by name

Popular brands

Yamaha YZF-R1 2015, Service Manual

Search results

Summary of Contents for YZF-R1 2015

Reviews:

Related manuals for YZF-R1 2015

Brands by name

Popular brands