Yamaha YZF-R1 2015 Service Manual Download Page 612 | Manualshive

Page: 612 / 704

background image

ABS (Anti-lock Brake System)

8-131

EAS31163

[A-4] ONLY THE ABS ECU FAILS TO COMMUNICATE

1. ABS ECU fuse

•

Check the ABS ECU fuse for continuity.
Refer to “CHECKING THE FUSES” on page 8-180.

•

If the ABS ECU fuse is blown, replace the fuse.

2. ABS ECU coupler

•

Check that the ABS ECU coupler is connected properly.
For information about connecting the ABS ECU coupler properly, refer to “INSTALLING THE HY-
DRAULIC UNIT ASSEMBLY” on page 4-69.

3. Wire harness

•

Open circuit between the main switch and the ABS ECU, or between the ABS ECU and the ground.
Check for continuity between brown/blue terminal of the main switch coupler and red/black terminal
of the ABS ECU coupler.
Check for continuity between black terminal of the ABS ECU coupler and the ground.
If there is no continuity, the wire harness is defective. Replace the wire harness.

•

Open circuit in the wire harness between the ABS ECU coupler and the Yamaha diagnostic tool cou-
pler.
Check for continuity between blue/white terminal of the ABS ECU coupler and blue/white terminal
of the Yamaha diagnostic tool coupler. (CANH)
Check for continuity between blue/black terminal of the ABS ECU coupler and blue/black terminal
of the Yamaha diagnostic tool coupler. (CANL)

4. ABS ECU malfunction

Replace the hydraulic unit assembly.

EAS31164

[A-5] ABS ECU AND FI ECU FAIL TO COMMUNICATE

1. Yamaha diagnostic tool

Check that the Yamaha diagnostic tool is properly connected.

2. Wire harness

•

Open circuit in the wire harness between the ABS ECU coupler and the Yamaha diagnostic tool cou-
pler.
Check for continuity between blue/white terminal of the ABS ECU coupler and blue/white terminal
of the Yamaha diagnostic tool coupler. (CANH)
Check for continuity between blue/black terminal of the ABS ECU coupler and blue/black terminal
of the Yamaha diagnostic tool coupler. (CANL)

EAS31165

[B-1] MALFUNCTION ARE CURRENTLY DETECTED

When the Yamaha diagnostic tool is connected to the Yamaha diagnostic tool coupler, the fault codes
will be displayed on the computer screen.

•

A fault code is displayed. [B-2]

•

A fault code is not displayed. [C-1]

EAS31166

[B-2] DIAGNOSIS USING THE FAULT CODES

This model uses the Yamaha diagnostic tool to identify malfunctions.
For information about using the Yamaha diagnostic tool, refer to the operation manual that is included
with the tool.

Connecting the Yamaha diagnostic tool
Removing the rider seat. Refer to “GENERAL CHASSIS (1)” on page 4-1.
Removing the protective cap “1”, and then connect the Yamaha diagnostic tool to the coupler.

Yamaha diagnostic tool

90890-03239

«
...
610
611
612
613
614
...
»

Summary of Contents for YZF-R1 2015

































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for YZF-R1 2015

Brand: SCA Pages: 5

Brand: ICON Vehicle Dynamics Pages: 4

Brand: Ericsson Pages: 44

Brand: LSL Pages: 4

Brand: hepco & becker Pages: 6

Brand: hepco & becker Pages: 2

Brand: hepco & becker Pages: 3

SPORTRACK 670915 00 01

Brand: hepco & becker Pages: 2

Lock-it 5064564 00 01

Brand: hepco & becker Pages: 2

Easyrack 6626526 01 01

Brand: hepco & becker Pages: 4

Easyrack 6614526 01 01

Brand: hepco & becker Pages: 4

Brand: hepco & becker Pages: 2

Brand: hepco & becker Pages: 3

Brand: APRILIA Pages: 170

Brand: Abus Pages: 4

Brand: Petzl Pages: 15

Brand: hepco & becker Pages: 2

Brand: Honda Pages: 191

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands