manualshive.com logo in svg

Yamaha YZF-R1 2015, Service Manual

Share
Download
Yamaha YZF-R1 2015 Service Manual Download Page 47

FEATURES

1-38

of system intervention.

LCS

LCS can be set to 1, 2, or OFF. Setting level 2
more  strongly  controls  power  engine  output,
while  setting  level  1  applies  less  system  inter-
vention. OFF disables the LCS function from the
selected YRC mode (the LCS icon will not ap-
pear and the launch control function cannot be
activated).
When LCS has been set to level 1 or 2 for the se-
lected YRC mode, the LCS indicator on the main
screen will appear in a grey color to indicate that
LCS is available. When the launch control sys-
tem has been activated (made ready for use via
the  mode  switch),  the  LCS  indicator  will  turn
white.

TIP

LCS works in conjunction with the LIF system.
LCS cannot be used if LIF is turned off.

QSS

QSS can be set to 1, 2, or OFF. Setting level 1
gives the fastest shifts, while setting level 2 gives
slightly  smoother  shifts.  OFF  turns  the  system
off  entirely,  and  the  clutch  lever  must  then  be
used when making upshifts.

TIP

Turning the QSS on or off does not affect any
other systems nor is QSS affected by the set-
tings of any other system.

LIF

LIF can be set to 1, 2, 3, or OFF. Setting level 3
most strongly reduces wheel lift, and setting lev-
el 1 provides the least amount of system inter-
vention.  OFF  turns  LIF  off  and  LCS  will  be
disabled for the selected YRC mode.

[To customize a YRC mode or adjust a YRC

item]

1. From  the  MENU  screen,  select  “YRC  Set-

ting”.

2. The “YRC Setting” screen is displayed, and

the  YRC  mode  box  “YRC”  is  highlighted.
Short push the wheel switch to enter the box
and then select the YRC mode; A, B, C, D,
that you want to adjust.

3. Select the YRC item; PWR, TCS, SCS, LCS,

QSS, LIF, or ERS (YZF-R1M) that you want
to adjust.

1. System intervention
2. Sideward slide

1

3
2

1

SCS

2

1. System intervention
2. Wheel lift

1. Triangle mark
2. YRC mode box
3. YRC item
4. ERS mode (YZF-R1M)
5. To ERS menu (YZF-R1M)

1

3
2

1

LIF

2

D

C

B

A

1

2
3
4

1
2

3

4

1

2

1
2

3

3

5

OFF

1

2

OFF

OFF

1

2

OFF

A-1

A-2

M-1
M-2

A-3

YRC

PWR TCS SCS LCS QSS LIF

ESC

YRC

PWR TCS SCS LCS QSS LIF

ERS

12:00  

YRC Setting

km/h

1

3

4

5

2

Summary of Contents for YZF-R1 2015

































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands