Yamaha YZF-R1 2015 Service Manual Download Page 645

Page: 645 / 704

ELECTRONICALLY ADJUSTABLE SUSPENSION SYSTEM (for

YZF-R1M)

8-164

Connection of SCU coupler.

Check the locking condition of

the coupler.

Disconnect the coupler and

check the pins (bent or broken

terminals and locking condition

of the pins).

Improperly connected

Con-

nect the coupler securely or

replace the wire harness.

Turn the main switch to “OFF”

and back to “ON”.

Fault code number is not dis-

played

Service is finished.

Fault code number is displayed

Go to item 3.

Connection of front fork step-

ping motor sub-lead coupler.

Check the locking condition of

the coupler.

Disconnect the coupler and

check the pins (bent or broken

terminals and locking condition

of the pins).

Improperly connected

Con-

nect the coupler securely or

replace the wire harness.

Turn the main switch to “OFF”

and back to “ON”.

Fault code number is not dis-

played

Service is finished.

Fault code number is displayed

Go to item 4.

Wire harness continuity.

Open circuit

Replace the

wire harness.

•

Between SCU coupler and left

front fork stepping motor.

green–green

green/black–green/black

green/red–green/red

green/blue–green/blue

•

Between SCU coupler and

right front fork stepping motor.

pink–pink

pink/black–pink/black

pink/white–pink/white

pink/blue–pink/blue

•

Between SCU coupler and

rear shock absorber assembly

stepping motor (compression

damping).

white–white

white/black–white/black

white/red–white/red

white/green–white/green

•

Between SCU coupler and

rear shock absorber assembly

stepping motor (rebound

damping).

yellow–yellow

yellow/black–yellow/black

yellow/red–yellow/red

yellow/green–yellow/green

Short-circuit

Replace the

wire harness.

•

Between left front fork step-

ping motor “1” and power

ground “2”.

green–black

green/black–black

green/red–black

green/blue–black

•

Between right front fork step-

ping motor “3” and power

ground “2”.

pink–black

pink/black–black

pink/white–black

pink/blue–black

Turn the main switch to “OFF”

and back to “ON”.

Fault code number is not dis-

played

Service is finished.

Fault code number is displayed

Go to item 5.

Fault code No.

Item

Stepping motor: open or short circuit detected.

Summary of Contents for YZF-R1 2015

































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for YZF-R1 2015

Reviews:

Related manuals for YZF-R1 2015

Brands by name

Popular brands

Yamaha YZF-R1 2015, Service Manual

Search results

Summary of Contents for YZF-R1 2015

Reviews:

Related manuals for YZF-R1 2015

Brands by name

Popular brands