Yamaha YZF-R1 2015 Service Manual Download Page 617

Page: 617 / 704

ABS (Anti-lock Brake System)

8-136

Vehicle system power supply

(voltage of ABS ECU power

supply is low)

Power voltage supplied to

the ABS ECU in the hydrau-

lic unit assembly is too low.

•

Defective battery

•

Defective coupler between

the battery and the hydrau-

lic unit assembly

•

Open or short circuit in the

wire harness between the

battery and the hydraulic

unit assembly

•

Defective charging system

Hydraulic unit assembly

(defective ABS ECU)

Abnormal data is detected in

the hydraulic unit assembly.

•

Defective hydraulic unit

assembly

Hydraulic unit assembly

(internal circuit abnormal)

Abnormality detected in of

hydraulic unit assembly.

•

Defective hydraulic unit

assembly

Vehicle CAN communication

line or power source of vehi-

cle system

Short-circuit in CAN commu-

nication line or the voltage

that supplies the hydraulic

unit assembly is too low.

•

Short-circuit in CAN com-

munication line

•

Defective battery

•

Defective coupler between

battery and hydraulic unit

assembly

•

Wire harness between bat-

tery and hydraulic unit is

interrupted or has short-cir-

cuited

•

Defective charging system

Power supply voltage failure

in pressure sensor

Abnormality detected in

pressure sensor power sup-

ply circuit of hydraulic unit

assembly.

•

Defective hydraulic unit

assembly

Defective front pressure sen-

sor

Abnormality detected in

pressure sensor circuit at

front master cylinder side of

hydraulic unit assembly.

•

Defective front brake line

•

Defective hydraulic unit

assembly

Defective rear pressure sen-

sor

Abnormality detected in

pressure sensor circuit at

rear master cylinder side of

hydraulic unit assembly.

•

Defective rear brake line

•

Defective hydraulic unit

assembly

Hydraulic unit assembly

(Defective front pressure

sensor)

Abnormality detected in

pressure sensor circuit at

front caliper side of hydrau-

lic unit assembly.

In case of electrical interlock-

ing brake

•

Defective front brake line

•

Defective hydraulic unit

assembly

Hydraulic unit assembly

(Defective rear pressure sen-

sor)

Abnormality detected in

pressure sensor circuit of

hydraulic unit assembly.

•

Defective rear brake line

•

Defective hydraulic unit

assembly

CAN communication

(between meter assembly

and hydraulic unit assembly)

Transmitted data from the

meter cannot be normally

received.

•

Defective coupler between

meter assembly and

hydraulic unit assembly

•

Harness is broken or short-

circuit between meter

assembly and hydraulic

unit assembly

•

Defective meter assembly

•

Defective hydraulic unit

assembly

Fault code

No.

Item

Symptom

Check point

Summary of Contents for YZF-R1 2015

































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for YZF-R1 2015

Reviews:

Brands by name

Popular brands

Yamaha YZF-R1 2015, Service Manual

Search results

Summary of Contents for YZF-R1 2015

Reviews:

Brands by name

Popular brands