Yamaha YZF-R1 2015 Service Manual Download Page 508

Page: 508 / 704

LIGHTING SYSTEM

8-27

EAS30499

TROUBLESHOOTING

Any of the following fail to light: headlight, auxiliary light, high beam indicator light, tail/brake light, li-
cense plate light or meter light.

TIP

•

Before troubleshooting, remove the following part(s):

1. Front side cowling/Front panel/Side cover
2. Passenger seat/Rider seat/Tail cover/Rear side cover
3. Headlight assembly

1. Check the fuses.

(Main, headlight, backup, ignition

and signaling system)

Refer to “CHECKING THE FUSES”

on page 8-180.

Replace the fuse(s).

2. Check the battery.

Refer to “CHECKING AND

CHARGING THE BATTERY” on

page 8-181.

•

Clean the battery terminals.

•

Recharge or replace the battery.

3. Check the main switch.

Refer to “CHECKING THE

SWITCHES” on page 8-177.

Replace the main switch/immobilizer unit.

4. Check the dimmer switch.

Refer to “CHECKING THE

SWITCHES” on page 8-177.

The dimmer switch is faulty. Replace the

left handlebar switch.

5. Check the pass/LAP switch.

Refer to “CHECKING THE

SWITCHES” on page 8-177.

The pass/LAP switch is faulty. Replace

the left handlebar switch.

6. Check the entire lighting system’s

wiring.

Refer to “CIRCUIT DIAGRAM” on

page 8-23.

Properly connect or repair the lighting sys-

tem’s wiring.

Replace the ECU, meter assembly,

headlight assembly, tail/brake light, li-

cense plate light or auxiliary light.

Refer to “REPLACING THE ECU (En-

gine Control Unit)” on page 8-180.

Summary of Contents for YZF-R1 2015

































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for YZF-R1 2015

Reviews:

Related manuals for YZF-R1 2015

Brands by name

Popular brands

Yamaha YZF-R1 2015, Service Manual

Search results

Summary of Contents for YZF-R1 2015

Reviews:

Related manuals for YZF-R1 2015

Brands by name

Popular brands