Yamaha YZF-R1 2015 Service Manual Download Page 335

Page: 335 / 704

CHAIN DRIVE

4-118

NOTICE

ECA19090

• This vehicle has a drive chain with small

rubber O-rings “1” between the drive chain

side plates. Never use high-pressure water

or air, steam, gasoline, certain solvents

(e.g., benzine), or a coarse brush to clean

the drive chain. High-pressure methods

could force dirt or water into the drive

chain’s internals, and solvents will deterio-

rate the O-rings. A coarse brush can also

damage the O-rings. Therefore, use only

kerosene to clean the drive chain.

• Do not soak the drive chain in kerosene for

more than ten minutes, otherwise the O-

rings can be damaged.

▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲

4. Check:

•

O-rings “1”
Damage

Replace the drive chain.

•

Drive chain rollers “2”
Damage/wear

Replace the drive chain.

•

Drive chain side plates “3”
Damage/wear/cracks

Replace the drive

chain.

5. Lubricate:

•

Drive chain

EAS30231

CHECKING THE DRIVE SPROCKET

1. Check:

•

Drive sprocket
More than 1/4 tooth “a” wear

Replace the

drive sprocket, the rear wheel sprocket and
the drive chain as a set.
Bent teeth

Replace the drive sprocket, the

rear wheel sprocket and the drive chain as a
set.

EAS30232

CHECKING THE REAR WHEEL SPROCKET

Refer to “CHECKING AND REPLACING THE
REAR WHEEL SPROCKET” on page 4-38.

EAS30233

CHECKING THE REAR WHEEL DRIVE HUB

Refer to “CHECKING THE REAR WHEEL
DRIVE HUB” on page 4-38.

Recommended lubricant

Chain lubricant suitable for

O-ring chains

b. Correct

1. Drive chain roller
2. Drive sprocket

Summary of Contents for YZF-R1 2015

































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for YZF-R1 2015

Reviews:

Brands by name

Popular brands

Yamaha YZF-R1 2015, Service Manual

Search results

Summary of Contents for YZF-R1 2015

Reviews:

Brands by name

Popular brands