Yamaha WaveRunner VX 700 Service Manual Download Page 97

Page: 97 / 181

5-28

Drive coupling removal and
installation

Remove the drive coupling.

TIP:

Install the drive coupling with the same spe-
cial service tools that were used for removal.

Flywheel magneto removal and
installation

Remove the flywheel magneto bolt.

TIP:

Install the bolt with the same special service
tool that was used for removal.

Remove the flywheel magneto.

NOTICE:

To prevent damage to the engine or
special service tools, screw in the fly-
wheel puller set bolts evenly and com-
pletely so that the puller plate is
parallel to the flywheel magneto.

TIP:

When installing the flywheel magneto,
degrease the flywheel magneto where it is
coupled to the crankshaft.

Drive coupling check

Check the drive coupling. Replace if
damaged or worn.

Flywheel magneto check

Check the ring gear. Replace if damaged
or worn.

Coupler wrench: 90890-06425
Flywheel holder: 90890-06522

Drive coupling:

36 N·m (3.6 kgf·m, 26.6 ft·lb)

Flywheel holder: 90890-06522

Flywheel magneto bolt:

74 N·m (7.4 kgf·m, 54.6 ft·lb)

Flywheel puller: 90890-06521

Starter clutch assy.

Summary of Contents for WaveRunner VX 700






















































































































































































Search results

Summary of Contents for WaveRunner VX 700

Reviews:

Related manuals for WaveRunner VX 700

Brands by name

Popular brands

Yamaha WaveRunner VX 700, Service Manual

Search results

Summary of Contents for WaveRunner VX 700

Reviews:

Related manuals for WaveRunner VX 700

Brands by name

Popular brands